Login
My Garage
  1. Home
  2. Recalls
  3. Audi Q2

Audi Q2 Recalls

There are currently 5 safety recalls out on the Audi Q2. To find out whether your car is affected, you'll need to find your car's VIN number.

How to find your VIN

The VIN can often be found on the lower-left corner of the dashboard, in front of the steering wheel.

You can read the number by looking through the windshield. The VIN may also appear in a number of other locations:

  • Front of the engine block. This should be easy to spot by opening the bonnet, and looking at the front of the engine.
  • Front of the car frame, near the container that holds windshield washer fluid.
  • Rear wheel well. Try looking up, directly above the tyre.
  • Inside the driver-side doorjamb. Open the door, and look underneath where the side-view mirror would be located if the door was shut.
  • Driver-side doorpost. Open the door, and look near the spot where the door latches, not too far from the seatbelt return.
  • Underneath the spare tyre.
VIN Location Diagram

If you still can't locate the VIN, try consulting your vehicle manual. Or, call a dealership or the manufacturer and request guidance.

Step 2 - See if your car is affected
  • Announcement date:
    22/07/2019
    Recalls number:
    R/2019/234
    VIN start:
    WAUZZZGA2KA047797
    VIN end:
    WAUZZZGA2KA047797
    Car Build Date:
    22/02/2019 - 22/02/2019
    Concern:
    Head Restraint Mounting May Not Be Correctly Welded To Rear Seat Outer Backrest Frame
    Defect:
    The mounting for the head restraint may not be correctly welded to the outer backrest frame for the rear seat.
    Remedy:
    The backrest on the rear seat bench must be checked and if necessary replaced.
  • Announcement date:
    30/11/2018
    Recalls number:
    R/2018/338
    VIN start:
    WAUZZZGA5JA104704
    VIN end:
    WAUZZZGA7JA106518
    Car Build Date:
    21/05/2018 - 03/09/2018
    Concern:
    The Mounting For The Head Restraint Is Not Correctly Welded To The Outer Backrest Frame For The Rear Seat
    Defect:
    The rear back rest head restraint mounting is not correctly welded.
    Remedy:
    Check and replace rear back rest frame if required.
  • Announcement date:
    25/10/2018
    Recalls number:
    R/2018/295
    VIN start:
    EAUZZZGA2JA000395
    VIN end:
    WAUZZZGA4JA108761
    Car Build Date:
    01/01/2017 - 30/06/2018
    Concern:
    The Electro-mechanical Parking Brake May Be Released While The Clutch Pedal Is Being Released
    Defect:
    The electro-mechanical park brake may be released inappropriately.
    Remedy:
    The software for the brake control will be updated.
  • Announcement date:
    25/10/2018
    Recalls number:
    R/2018/295
    VIN start:
    WAUZZZGA6HA020806
    VIN end:
    WAUZZZGA7HA059825
    Car Build Date:
    01/01/2017 - 30/06/2018
    Concern:
    The Electro-mechanical Parking Brake May Be Released While The Clutch Pedal Is Being Released
    Defect:
    The electro-mechanical park brake may be released inappropriately.
    Remedy:
    The software for the brake control will be updated.
  • Announcement date:
    17/11/2017
    Recalls number:
    R/2017/311
    VIN start:
    WAUZZZGA3JA025211
    VIN end:
    WAUZZZGA7JA025552
    Car Build Date:
    01/08/2017 - 31/08/2017
    Concern:
    Rear Hub Carriers Not Manufactured To Correct Standard
    Defect:
    The hardening process for the rear wheel bearing housings may not have been correctly performed. In the worst case this could lead to a fractured housing. Should a fractured housing occur there would be abnormal noises bad tyre wear and a theoretical possibility of wheel loss.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the right and left rear wheel bearing housings.
Step 3 - Contact your nearest dealer

Enter your postcode to see your nearest franchised dealer: