Login
My Garage
  1. Home
  2. Recalls
  3. Honda Jazz

Honda Jazz Recalls

There are currently 55 safety recalls out on the Honda Jazz. To find out whether your car is affected, you'll need to find your car's VIN number.

How to find your VIN

The VIN can often be found on the lower-left corner of the dashboard, in front of the steering wheel.

You can read the number by looking through the windshield. The VIN may also appear in a number of other locations:

  • Front of the engine block. This should be easy to spot by opening the bonnet, and looking at the front of the engine.
  • Front of the car frame, near the container that holds windshield washer fluid.
  • Rear wheel well. Try looking up, directly above the tyre.
  • Inside the driver-side doorjamb. Open the door, and look underneath where the side-view mirror would be located if the door was shut.
  • Driver-side doorpost. Open the door, and look near the spot where the door latches, not too far from the seatbelt return.
  • Underneath the spare tyre.
VIN Location Diagram

If you still can't locate the VIN, try consulting your vehicle manual. Or, call a dealership or the manufacturer and request guidance.

Step 2 - See if your car is affected
  • Announcement date:
    09/08/2022
    Recalls number:
    R/2022/221
    VIN start:
    JHMGR3890MS200015
    VIN end:
    JHMGR6880NS200379
    Car Build Date:
    29/01/2020 - 29/01/2021
    Concern:
    The Front Wide Camera May Not Start Up In The Correct Way After The Vehicle Has Started
    Defect:
    The front wide camera may not start up in the correct way after the vehicle is started.
    Remedy:
    Change the software in the Front Wide Camera.
  • Announcement date:
    14/08/2020
    Recalls number:
    R/2020/194
    VIN start:
    JHMGK3***LS209584
    VIN end:
    JHMGK3***LS211533
    Car Build Date:
    28/08/2019 - 25/09/2019
    Concern:
    Due To Incorrect Manufacturing The Rear Seat Belt Assembly Webbing Sensor Could Become Inoperative
    Defect:
    The webbing sensor in the rear centre seat belt assembly could become inoperative.
    Remedy:
    Check and if the seat belt is within the affected range the seat belt will be replaced.
  • Announcement date:
    29/08/2019
    Recalls number:
    R/2019/245
    Car Build Date:
    17/12/2003 - 09/11/2011
    Concern:
    Possible Air Bag Inflator Rupture
    Defect:
    Driver air bag may not deploy correctly.
    Remedy:
    The inflator inside the drivers airbag module is to be replaced.
  • Announcement date:
    29/08/2019
    Recalls number:
    R/2019/243
    Car Build Date:
    17/11/2000 - 16/12/2014
    Concern:
    Possible Air Bag Inflator Rupture
    Defect:
    Passenger air bag may not deploy correctly.
    Remedy:
    The inflator inside the passenger
  • Announcement date:
    29/08/2019
    Recalls number:
    R/2019/246
    Car Build Date:
    26/06/2007 - 21/05/2014
    Concern:
    Possible Air Bag Inflator Rupture
    Defect:
    Driver air bag may not deploy correctly.
    Remedy:
    The inflator inside the drivers airbag module is to be replaced.
  • Announcement date:
    30/01/2019
    Recalls number:
    R/2018/342
    VIN start:
    JHMGE6*****200004
    VIN end:
    SHHGG6*****024191
    Car Build Date:
    04/02/2010 - 20/05/2015
    Concern:
    Takata Passenger Airbag Inflator May Rupture
    Defect:
    Passenger airbag inflators may not operate as intended.
    Remedy:
    Replacement of Airbag Assembly on affected vehicles.
  • Announcement date:
    23/02/2018
    Recalls number:
    R/2018/029
    VIN start:
    SHHGG6***AU000101
    VIN end:
    SHHGG6***AU015430
    Car Build Date:
    01/12/2009 - 28/05/2010
    Concern:
    Passenger Airbag May Fail To Deploy Correctly
    Defect:
    The propellant used in certain air bag inflators may degrade over time due to heat cycles and exposure to moisture. In the event that the airbag is activated it may overinflate due to overly aggressive combustion of the propellant. The excessive internal pressure may cause the inflator body to rupture and metal fragments may pass through the cushion material possibly causing severe injury to the vehicle occupants.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the airbag inflator unit.
  • Announcement date:
    23/02/2018
    Recalls number:
    R/2018/029
    VIN start:
    SHHGG5***AU000101
    VIN end:
    SHHGG5***AU003040
    Car Build Date:
    02/12/2009 - 21/05/2010
    Concern:
    Passenger Airbag May Fail To Deploy Correctly
    Defect:
    The propellant used in certain air bag inflators may degrade over time due to heat cycles and exposure to moisture. In the event that the airbag is activated it may overinflate due to overly aggressive combustion of the propellant. The excessive internal pressure may cause the inflator body to rupture and metal fragments may pass through the cushion material possibly causing severe injury to the vehicle occupants.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the airbag inflator unit.
  • Announcement date:
    28/03/2017
    Recalls number:
    R/2017/017
    VIN start:
    SHHGG68809U000101
    VIN end:
    SHHGG68809U004330
    Car Build Date:
    04/07/2008 - 04/01/2010
    Concern:
    Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the passenger's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment
    Remedy:
    On affected vehicles replace the inflator inside the passenger's air bag module.
  • Announcement date:
    28/03/2017
    Recalls number:
    R/2017/017
    VIN start:
    SHHGG57309U000101
    VIN end:
    SHHGG57309U001780
    Car Build Date:
    04/07/2008 - 04/01/2010
    Concern:
    Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the passenger's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment
    Remedy:
    On affected vehicles replace the inflator inside the passenger's air bag module.
  • Announcement date:
    28/03/2017
    Recalls number:
    R/2017/017
    VIN start:
    JHMGE67809S222991
    VIN end:
    JHMGE67609S243238
    Car Build Date:
    04/07/2008 - 04/01/2010
    Concern:
    Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the passenger's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment
    Remedy:
    On affected vehicles replace the inflator inside the passenger's air bag module.
  • Announcement date:
    28/03/2017
    Recalls number:
    R/2017/017
    VIN start:
    JHMGG17309S206862
    VIN end:
    JHMGG17409S211390
    Car Build Date:
    04/07/2008 - 04/01/2010
    Concern:
    Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the passenger's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment
    Remedy:
    On affected vehicles replace the inflator inside the passenger's air bag module.
  • Announcement date:
    28/03/2017
    Recalls number:
    R/2017/017
    VIN start:
    LUCGG375093200015
    VIN end:
    LUCGG386093220242
    Car Build Date:
    04/07/2008 - 04/01/2010
    Concern:
    Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the passenger's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment
    Remedy:
    On affected vehicles replace the inflator inside the passenger's air bag module.
  • Announcement date:
    28/03/2017
    Recalls number:
    R/2017/017
    VIN start:
    LUCGG275093200011
    VIN end:
    LUCGG275093219182
    Car Build Date:
    04/07/2008 - 04/01/2010
    Concern:
    Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the passenger's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment
    Remedy:
    On affected vehicles replace the inflator inside the passenger's air bag module.
  • Announcement date:
    16/05/2016
    Recalls number:
    R/2016/045
    VIN start:
    JHMGE67809S200015
    VIN end:
    JHMGP1850FS203168
    Car Build Date:
    02/03/2004 - 20/05/2015
    Concern:
    Drivers Airbag Inflator May Rupture If Deployed
    Defect:
    Abnormal deployment pressure may lead to rupture of the driver's air bag inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment.
    Remedy:
    On affected vehicles replace the inflator inside the driver's air bag module.
  • Announcement date:
    23/10/2015
    Recalls number:
    R/2015/143
    VIN start:
    LUCGE271073206062
    VIN end:
    LUCGE387083229490
    Car Build Date:
    02/01/2007 - 28/12/2011
    Concern:
    Drivers Airbag May Rupture If Deployed
    Defect:
    Due to abnormal pressure the driver's air bag inflator case may rupture during deployment. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.
    Remedy:
    On affected vehicles replace the inflator inside the drivers airbag module.
  • Announcement date:
    23/10/2015
    Recalls number:
    R/2015/143
    VIN start:
    JHMGD17507S212044
    VIN end:
    JHMGD57308S202905
    Car Build Date:
    02/01/2007 - 28/12/2011
    Concern:
    Drivers Airbag May Rupture If Deployed
    Defect:
    Due to abnormal pressure the driver's air bag inflator case may rupture during deployment. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.
    Remedy:
    On affected vehicles replace the inflator inside the drivers airbag module.
  • Announcement date:
    29/06/2015
    Recalls number:
    R/2015/103
    VIN start:
    LUCGE273053200017
    VIN end:
    LUCGE375073202553
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Drivers Airbag May Rupture If Deployed
    Defect:
    Abnormal deployment pressure may lead to rupture of the inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.
    Remedy:
    On affected vehicles replace the drivers airbag module.
  • Announcement date:
    29/06/2015
    Recalls number:
    R/2015/104
    VIN start:
    JHMGD17504S205055
    VIN end:
    JHMGD57308S201153
    Car Build Date:
    25/12/2003 - 29/12/2008
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the inflator case. In the event of an inflator rupture metal fragments could be propelled upward toward the windshield or downward toward the front passenger
    Remedy:
    On affected vehicles replace the inflator inside the front passenger
  • Announcement date:
    29/06/2015
    Recalls number:
    R/2015/104
    VIN start:
    LUCGE273063200001
    VIN end:
    LUCGE377083208730
    Car Build Date:
    25/12/2003 - 29/12/2008
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the inflator case. In the event of an inflator rupture metal fragments could be propelled upward toward the windshield or downward toward the front passenger
    Remedy:
    On affected vehicles replace the inflator inside the front passenger
  • Announcement date:
    29/06/2015
    Recalls number:
    R/2015/104
    VIN start:
    JHMGE67809S200015
    VIN end:
    JHMGG17409S207287
    Car Build Date:
    25/12/2003 - 29/12/2008
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the inflator case. In the event of an inflator rupture metal fragments could be propelled upward toward the windshield or downward toward the front passenger
    Remedy:
    On affected vehicles replace the inflator inside the front passenger
  • Announcement date:
    29/06/2015
    Recalls number:
    R/2015/104
    VIN start:
    LUCGG275093200013
    VIN end:
    LUCGG374093206983
    Car Build Date:
    25/12/2003 - 29/12/2008
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the inflator case. In the event of an inflator rupture metal fragments could be propelled upward toward the windshield or downward toward the front passenger
    Remedy:
    On affected vehicles replace the inflator inside the front passenger
  • Announcement date:
    29/06/2015
    Recalls number:
    R/2015/104
    VIN start:
    MRHGM15209P010001
    VIN end:
    MRHGM16609P050438
    Car Build Date:
    25/12/2003 - 29/12/2008
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    Abnormal deployment pressure may lead to rupture of the inflator case. In the event of an inflator rupture metal fragments could be propelled upward toward the windshield or downward toward the front passenger
    Remedy:
    On affected vehicles replace the inflator inside the front passenger
  • Announcement date:
    29/06/2015
    Recalls number:
    R/2015/103
    VIN start:
    JHMGD18504S215442
    VIN end:
    JHMGD57307S203184
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Drivers Airbag May Rupture If Deployed
    Defect:
    Abnormal deployment pressure may lead to rupture of the inflator case. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.
    Remedy:
    On affected vehicles replace the drivers airbag module.
  • Announcement date:
    16/03/2015
    Recalls number:
    R/2015/043
    VIN start:
    JHMGD1**03S211931
    VIN end:
    JHMGD5**04S201690
    Car Build Date:
    02/01/2003 - 27/12/2003
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant or in a thermal issue in the interior compartment which may lead to fire.
    Remedy:
    Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.
  • Announcement date:
    05/01/2015
    Recalls number:
    R/2014/158
    VIN start:
    JHMGD1**04S200199
    VIN end:
    JHMGD1**04S215323
    Car Build Date:
    10/06/2003 - 02/09/2004
    Concern:
    Drivers Airbag May Rupture If Deployed
    Defect:
    The drivers front airbag inflator could produce excessive internal pressure. If an affected airbag deploys the increased internal pressure may cause the inflator to rupture. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the inflator inside the drivers airbag module with a new one.
  • Announcement date:
    05/01/2015
    Recalls number:
    R/2014/158
    VIN start:
    JHMGD5**04S200001
    VIN end:
    JHMGD5**04S203808
    Car Build Date:
    10/06/2003 - 02/09/2004
    Concern:
    Drivers Airbag May Rupture If Deployed
    Defect:
    The drivers front airbag inflator could produce excessive internal pressure. If an affected airbag deploys the increased internal pressure may cause the inflator to rupture. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.
    Remedy:
    Recall the vehicles that are likely to be affected and replace the inflator inside the drivers airbag module with a new one.
  • Announcement date:
    27/08/2013
    Recalls number:
    R/2013/076
    Car Build Date:
    11/07/2001 - 31/07/2008
    Concern:
    Risk Of Fire
    Defect:
    Water and other liquids may enter the driver's side power window switch and may cause damage switch failure overheating and potentially a fire.
    Remedy:
    Recall affected vehicles and replace driver's side power window switch.
  • Announcement date:
    17/04/2013
    Recalls number:
    R/2013/049
    VIN start:
    JHMGD57702S200006
    VIN end:
    JHMGD57702S215052
    Car Build Date:
    21/09/2001 - 20/12/2002
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant or in a thermal issue in the interior compartment which may lead to fire.
    Remedy:
    Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.
  • Announcement date:
    17/04/2013
    Recalls number:
    R/2013/049
    VIN start:
    JHMGD57703S200004
    VIN end:
    JHMGD57703S206085
    Car Build Date:
    25/12/2002 - 23/04/2003
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant or in a thermal issue in the interior compartment which may lead to fire.
    Remedy:
    Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.
  • Announcement date:
    17/04/2013
    Recalls number:
    R/2013/049
    VIN start:
    JHMGD18503S201850
    VIN end:
    JHMGD17503S219916
    Car Build Date:
    25/12/2002 - 23/04/2003
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant or in a thermal issue in the interior compartment which may lead to fire.
    Remedy:
    Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.
  • Announcement date:
    17/04/2013
    Recalls number:
    R/2013/049
    VIN start:
    JHMGD17802S200019
    VIN end:
    JHMGD17302S253068
    Car Build Date:
    21/09/2001 - 27/12/2002
    Concern:
    Passenger Side Airbag May Fail To Deploy Correctly
    Defect:
    The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant or in a thermal issue in the interior compartment which may lead to fire.
    Remedy:
    Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.
  • Announcement date:
    05/02/2013
    Recalls number:
    R/2013/013
    VIN start:
    SHHGG6780CU000269
    VIN end:
    SHHGG688ODU006882
    Car Build Date:
    18/08/2010 - 18/09/2012
    Concern:
    Brake Fluid May Leak
    Defect:
    The left hand front brake pipe may not be fully secure which could lead to the brake pipe chafing on the EGR pipe. If this occurs and remains unseen the damage could result in loss of brake fluid and the attendant loss of braking efficiency.
    Remedy:
    Recall the vehicles that are likely to be affected to replace and correctly secure the left hand front brake pipe.
  • Announcement date:
    16/07/2012
    Recalls number:
    R/2012/071
    Car Build Date:
    01/01/1970 - 01/01/1970
    Concern:
    Transmission May Malfunction
    Defect:
    In rare circumstances the gear indicator may display neutral when the gearbox is in reverse gear. If this happens the vehicle may reverse unexpectedly and cause an incident.
    Remedy:
    Recall vehicles likely to be affected to correct the unit software and inspect the reverse shift holder for deformation. Where necessary the reverse shift piece and shift holder will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD5***2S200009
    VIN end:
    JHMGD5***2S215052
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD5***3S200004
    VIN end:
    JHMGD5***3S210242
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD1***2S200193
    VIN end:
    JHMGD1***2S253068
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD5***5S200002
    VIN end:
    JHMGD5***5S237852
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD1***7S200230
    VIN end:
    JHMGD1***7S234493
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD5***6S200001
    VIN end:
    JHMGD5***6S213236
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD1***6S200001
    VIN end:
    JHMGD1***6S248083
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD1***5S200004
    VIN end:
    JHMGD1***5S293283
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD5***7S200001
    VIN end:
    JHMGD5***7S208252
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD1***3S201849
    VIN end:
    JHMGD1***3S249242
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD1***8S200001
    VIN end:
    JHMGD1***8S219455
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD1***4S200008
    VIN end:
    JHMGD1***4S247249
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD5***8S200001
    VIN end:
    JHMGD5***8S202905
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    24/01/2011
    Recalls number:
    R/2010/228
    VIN start:
    JHMGD5***4S200001
    VIN end:
    JHMGD5***4S212382
    Car Build Date:
    22/10/2001 - 24/07/2008
    Concern:
    Headlights May Not Illuminate Correctly
    Defect:
    Due to the layout of the lighting switch wiring harness the low beam headlight circuit can be pulled tighter than other wires. After repeated use of the headlight switch the low beam terminal can become worn and poor electrical continuity may result from an accumulation of copper oxide. In some cases the poor continuity the poor continuity or melted terminal ends will cause the wiring harness terminal ends to melt. Poor continuity or melted terminal ends will cause the low beam head lights to become inoperative increasing the risk of accident.
    Remedy:
    The dealer will inspect the low beam terminal if the terminal shows signs of melting the lighting switch and low beam terminal harness will be replaced. If the terminal is not melted the low beam terminal harness will be replaced.
  • Announcement date:
    09/08/2010
    Recalls number:
    R/2010/090
    VIN start:
    SHHGG57309U000101
    VIN end:
    SHHGG5730AU003037
    Car Build Date:
    30/09/2009 - 21/05/2010
    Concern:
    Tyre May Deflate Without Warning
    Defect:
    The sidewall of the tyre may have been damaged during fitting to steel wheels. If the sidewall is weakened a bulge may be seen prior to the tyre deflating suddenly. If the tyre deflates suddenly control of the vehicle may become difficult.
    Remedy:
    Recall the vehicles that are likely to be affected to replace the four tyres on the standard steel road wheels.
  • Announcement date:
    22/06/2010
    Recalls number:
    R/2010/053
    VIN start:
    SHHGG6**0AU004959
    VIN end:
    SHHGG6**0AU011282
    Car Build Date:
    02/02/2010 - 06/04/2010
    Concern:
    Brake Pedal Travel
    Defect:
    The footbrake pedal is connected to the master cylinder via the brake pedal pin. It is possible that the retaining clip/locking pin that locks the footbrake pedal pin may not have been installed. If this is the case it is possible that the brake pedal pin may become detached. This will result in an increase in pedal travel and a corresponding increase in stopping distance.
    Remedy:
    Recall all affected vehicle and check for presence of retaining clip/locking pin. If found to be missing a new clip/pin will be installed.
  • Announcement date:
    22/06/2010
    Recalls number:
    R/2010/053
    VIN start:
    SHHGG5**0AU001211
    VIN end:
    SHHGG5**0AU002017
    Car Build Date:
    02/02/2010 - 06/04/2010
    Concern:
    Brake Pedal Travel
    Defect:
    The footbrake pedal is connected to the master cylinder via the brake pedal pin. It is possible that the retaining clip/locking pin that locks the footbrake pedal pin may not have been installed. If this is the case it is possible that the brake pedal pin may become detached. This will result in an increase in pedal travel and a corresponding increase in stopping distance.
    Remedy:
    Recall all affected vehicle and check for presence of retaining clip/locking pin. If found to be missing a new clip/pin will be installed.
  • Announcement date:
    02/02/2010
    Recalls number:
    R/2010/007
    Car Build Date:
    11/07/2001 - 31/07/2008
    Concern:
    Risk Of Fire
    Defect:
    Water and other liquids may enter the driver's side power window switch and may cause damage switch failure overheating and potentially a fire.
    Remedy:
    Recall affected vehicles check switch and wiring if damaged replace and then fit external cover to switch to prevent water ingress.
  • Announcement date:
    12/11/2008
    Recalls number:
    R/2008/161
    Car Build Date:
    17/05/2004 - 19/12/2005
    Concern:
    Handbrake Could Become Inoperative.
    Defect:
    It has been identified that the handbrake lever ratchet may not latch into position when the handbrake is applied due to the possibility of the internal push rod possibly having suffered damage during assembly. With continued usage the push rod joint can become worn causing the handbrake ratchet mechanism not to latch sufficiently. Should this occur the handbrake will become inoperative.
    Remedy:
    Recalled vehicles will have the handbrake mechanism replaced.
  • Announcement date:
    05/04/2007
    Recalls number:
    R/2007/061
    Car Build Date:
    01/05/2005 - 31/05/2005
    Concern:
    Engine May Cut Out
    Defect:
    The fuel pump relay may fail which will result in either the engine not starting or stalling.
    Remedy:
    Recall the vehicles that are likely to be affected to check and where necessary place the fuel pump relay.
  • Announcement date:
    24/05/2004
    Recalls number:
    R/2004/034
    VIN start:
    JHMGD17902S200005
    VIN end:
    JHMGD17702S200192
    Car Build Date:
    06/07/2001 - 21/09/2001
    Concern:
    Low Beam Headlights May Not Operate.
    Defect:
    Dipped beam headlights may malfunction either when switched on or during driving.
    Remedy:
    Recall likely to be affected vehicles and replace the headlight switch with a modified part. Additionally the terminal for dipped beam operation within the wiring harness will also be changed in order to rectify any heat damage that may have occurred.
Step 3 - Contact your nearest dealer

Enter your postcode to see your nearest franchised dealer: